September 1, 2009

The Variable Speed Zebra is a microprocessor-controlled tool that performs the following 3 major functions with ECM (variable speed) systems:

• Diagnostics - The Variable Speed Zebra is used in-line, between the furnace control board and the motor
• Control - Exercise the system in any mode the motor can be operated in
• Set-up - Provides a digital readout of a system's CFM and RPM to assist in set-up

The unit includes two DVDs:

• ECM System Theory
• ECM System Troubleshooting

(Click image for more details.)

The ZebraStat is a low-voltage HVAC/R diagnostic tool with the following primary functions:

• Up to six immediate continuity checks
• Acts as a remote control
• Visually displays signal levels on control lines
• Monitors voltage levels
• Acts as an automatically-resetting circuit breaker

(Click image for more details.)

The UZ-1 is able to test run a motor in one or more (up to six) speeds. It has seven LEDs and three 3-way switches. It arrives with one popular Adapter, which fits the very common GE/Regal-Beloit Series 2.0 and 2.3 motors. It is housed in a rugged, latchable case that protects the tool, the harness, and the power input clips. Inside the lid is a place for each Adapter's corresponding magnetic overlay card, which describes the functions of each switch and LED with respect to that specific motor series.

(Click image for more details.)

These extension harnesses extend the reach of your variable speed zebra. Two (2) 40" extension ribbon cables.

(Click image for more details.)

This 2-piece adapter set is required to connect your Variable Speed Zebra to the new X-13 ECM (variable speed) and Evergreen Motors by GE. Instructions included on DVD.

(Click image for more details.)

This 3-piece adapter set allows the technician to connect the variable speed zebra to the new condensing unit ECM (multi-speed, variable torque) motors by General Electric. Instructions are included on the DVD.

(Click image for more details.)

This device protects your expensive ECM motors from transient, surge, lightning, and spike voltages. This plug-in device is fast and convenient.

(Click image for more details.)

This device protects your expensive X-13 and Evergreen type ECM motors from transient, surge, lightning, and spike voltages. This plug-in device is fast and convenient.

(Click image for more details.)

This Adapter fits the GENTEQ 3.0 Series motors. It has a 4-pin motor plug.

(Click image for more details.)

This Adapter fits the GE X-13 Motors and many popular "X-Motor" motors. It has a 5-position plug that fits what look like 5 male quick-connects on the motor.

(Click image for more details.)

This Adapter fits the ECM 142 Multi-Speed Signal Controlled Condensing Unit Fan Motors

(Click image for more details.)

This Adapter fits the EVERGREEN IM motors. (It does not work with the Evergreen AH motor, which is no longer in production).

(Click image for more details.)

This Adapter fits the common GE/Regal-Beloit Series 2.0 and 2.3 motors. It has a 16-pin motor plug (2 rows of 8 pins). This adapter is included with the UZ-1.

(Click image for more details.)

The Zebra'Dapter is a fused power tap cordset which provides a significantly safer way to use 120VAC power to test:

• Motors
• Blowers
• Other Components and Systems

The lighted 120VAC plug confirms available voltage and the inline fuse makes your jobsite safer.

(Click image for more details.)

The Zebra'Dapter is a fused power tap cordset which provides a significantly safer way to obtain 120VAC power from:

• Condensing Units
• Attics & HVAC Closets
• New Construction Sites

The lighted 120VAC receptacle shows relative voltage and the inline fuse makes your jobsite safer.

(Click image for more details.)

8 medium Alligator Jumper Wires for use on motor circuits.

• 24" Length
• 8 Wires in 8 Colors
• 18 AWG (15A) Wire
• Velcro Tie/Hang Strap
• Soldered, not just crimped
• Heavy gauge, resealable bag

(Click image for more details.)

This plug and harness fits the newest style of Evergreen motor, called the Evergreen "IM". It is a 4-position connector.

(Click image for more details.)

4 large Alligator Jumper Wires for use on motor circuits.

• 24" Length
• 4 Wires in 4 Colors
• 14 AWG (30A) Wire
• Velcro Tie/Hang Strap
• Soldered, not just crimped
• Heavy gauge, resealable bag

(Click image for more details.)

This plug and harness fits all X-Motors, X-13 Motors, and the early Evergreen motors (Evergreen "AH" series). It appears to be a 5-position connector, but actually has one position blocked off.

(Click image for more details.)

This kit can repair many GE (Regal-Beloit) ECM motor modules that have been damaged by voltage problems and power surges.

Requires the use of a soldering gun and rosin-core solder.

(Click image for more details.)

10 small Alligator Jumper Wires for use on control circuits.

• 36" Length
• 10 Wires in 5 Colors
• 22 AWG (6A) Wire
• Velcro Tie/Hang Strap
• Soldered, not just crimped
• Heavy gauge, resealable bag

(Click image for more details.)

A rugged, protective case (10.5" x 7") that protects your UZ-1, your Adapters, and Motor Power Plugs from loss or damage.

(Click image for more details.)

This plug and harness fits the common GE/Regal-Beloit/GENTEQ Series 2.0, 2.3, 2.5 and 3.0 motors. It has a 5-pin motor plug (1 row of 5 pins). The motors can be either 120V or 240V, the plug/harness allows you to test any voltage motor with EITHER 120V or 240V on your bench.

(Click image for more details.)

It’s possible that your main harness might get cut or damaged by a blower — it’s easily replaced. Or use this as an EXTENSION!

(Click image for more details.)

Includes 1 set of 3 terminals, wires, and connectors

This compressor terminal repair kit features:

• Terminals are high temperature soldered, not just crimped
• Heavy duty 10AWG wire
• Special terminals allow clearance for compressor posts and lay flat under the safety cover

(Click image for more details.)